My Cart | Bookmark and Share
How To Apply

Instructions for Rhinestone Heat Transfers

 
how to apply
Your transfers will be delivered as a shiny sheet of rhinestones with a white or translucent backing. Do not remove the backing until you are ready to use the transfer. You will need:  either an iron (preferably with NO steam holes) or a 'heat press', an ironing board (if you are using an iron), scrapes of old sheets or muslin (or Teflon Sheets (muslin works just as well). Suitable Fabrics: any fabric that can withstand a minimum of 300-325 degrees F,  (wool setting on iron). These generally include: cotton, wool, Lycra, stretch Velour, Polyesters, nylon, Linen, Denim, Silk.
 
 Therefore, most T-shirts, Leotards, shirts, skirts, Jeans, pants, blouses, hats, and sweaters are suitable. BUT! Test iron or heat press at settings advised by applying heat to area and applying heat with Medium pressure for 25-30 seconds. Colored items may change color when hot, but usually return to normal when they cool. IF any damage due to heat (melting, scorching, etc.) the item is unsuitable for transfer work. Be very careful of Acrylics, Acetates (generally unfriendly to this process), and anything white. If discoloration occurs to white T-Shirts, this will usually disappear when washed, but testing is the operative word. Rogenstudio.com takes NO responsibility for damage to garments during this process....common sense rules!  
 

 

Heat Transfer Process

1. Arrange garment on ironing board or heat press so that transfer can be applied. If garment is arranged so that front and back are 'stacked' (such as T-shirt placed on ironing board with both front and back as two layers), then insert a scrape of clean muslin, bed sheet, or Teflon Sheet between layers...this will prevent adhesive from going through front layer and bonding to back.
 
2. Examine the transfer carefully. If any rhinestones have moved during shipping, now is the time to repair design (very rare occurrence, but can happen). Repair by removing backing, reposition  stray rhinestone(s)  with tweezers and replace shiny-side-down on sticky side of tape.  The errant rhinestone(s) will stay where placed.  IF all is well, then: peel off backing of Transfer. The 'Tacky Tape' of the transfer is very sticky, so place transfer carefully where you want it (you will not be able to move the rhinestones once they are heat bonded to fabric!
 
3. Cover the transfer with a scrape of clean muslin or Teflon Sheet. 
 
4. Apply heat by lowering iron straight down on transfer area and push hard for 25-30 seconds. DO NOT move iron around! You will dis-center rhinestones.  If you are using a heat press, adjust pressure to about 25 pounds pressure...do not over press, you will leave pressure marks on garment.
 
5. Remove iron/open heat press, allow to cool for about 10=15 seconds, then remove Tacky Tape. (do not allow Tacky Tape to remain on area, remove when still warm to touch). The rhinestones will remain on garment. The Tacky Tape may pull up nap which is visible, but you can re-iron and this will disappear. 
 
6. Test stones by gently picking at them. They should be well attached. Do not try to pull them off with too much picking! You will succeed!
 
7. We advise hand washing/turn garment inside out and drying at low heat.  Generally, rhinestones of 6SS, 10SS, and 12SS are very hardy, 16SS, 20SS, and 30SS are less hardy, so care for your garments with common sense.

 

Our Partners

Rogen Studio is excited to offer specialty screen prints that will give you a distinctive and unique look to accent your garments.

http://rogenstudio.com/screenprint

OUR RECOMMENDED SITES

Giddy Up Rides | Giddy Up Horses | 3D Face Dolls

With over 2500 clients only Rogen Studio label division offers our clients the unbeatable combination of trendy designs, distinctive materials and the latest in technology / manufacturing concepts.

http://rogenstudio.com/labelfactory

Newsletter




?>